Introduction: Boba Fett Mithosaur

In this tutorial, I will show you how to build the famed Boba Fett symbolisation called the Mithosaur. This project would be unblemished on the wall of any Boba Fett rabid. We will be victimisation the cutouts of the Mithosaur to make a second Mithosaur that is projecting out from the woodwind. This project is not too hard and the actual cutting time shouldn't take all-night. I hope you enjoy this project as much Eastern Samoa I have. Currently, the Mithosaur with the cutouts is on my wall with a flashlight behind information technology making IT into a nighttime light.

Stone's throw 1: Download the Pattern.

First of all, follow the link below, download the image that pops finished and enlarge to 223% (this is just what I enlarged it to because it fit on a regular piece of printing machine paper. Information technology can make up whatever size you like)

https://World Wide Web.google.com/search?q=boba+fett+symbol&r...

NOTE.. This pattern does not lie in to Pine Tree State and I don't personal the Copywrite! You cannot sell this without the owners permission!

Step 2: Things You Will Need.

You will need a scrollsaw. Some scrollsaw will do, but rather one that uses pinless blades. I employment a Delta 16 in. You will need an assortment of thin-tooth to medium tooth fretsaw blades.( I really did the entire figure with one blade) To transfer the pattern onto my wood I secondhand a copying film. There are other ways to transfer the pattern just this is the easiest way. The wood I old was 1/4 inch oak plywood, just at that place are many, many different types of wood so you can be creative here. The size up is too busy your discretion, I am planning to supply a frame so I made mine 1/4 in larger on all sides than the border of a classical piece of music of printer paper.(very precise!) Just make sure that all the edges are satisfying. You will also need the smallest recitation scra you backside find, I used a 1/32 in.

Mistreat 3: Transfering the Pattern.

Now that you have printed the shape place a piece of copying film on the wood and the put away your radiation diagram connected top of that. After direction your pattern along the wood, use a pen to trace around the edges of the black lines. The copying pic gets pushed down and leaves the same line underneath. It is important to be too-careful when drawing off this line as it leave be the line you are cutting.

Step 4: Drill the Holes.

Drill your holes right the lines. Note, I cut the center slice out before I took the photos. You rump silent visit where I drilled the holes. When you cut everything unconscious tardive, you leave have to straighten the edges where you drilled.

Ill-use 5: Extirpation.

After you have trained the holes you fundament begin to thread the blade through with a stochastic hole. (IT doesn't actually matter I did the middle piece before I started to proceeds pictures but the process is tranquil the like). The one thing that was difficult for me, was the fact that some sides of the cut will personify used. In to the highest degree scrollsaw work you shake off the scraps. We are going to employment the scraps. this partially of the work is hard to show you how. However, I can give much guidelines. Do not whirl backwards with the vane to try to desexualize a mistake! This project has so many curves you will probably ne'er see a misunderstanding. If you get over backwards you testament shipwreck at least one side of the project. As you complete each cut, clean up around the bore-hole so that you cannot see the hole out connected either piece.

Tone 6: Sanding, Painting, Gluing, and Finishing

Sand all of the pieces of Grant Wood smooth. I stained both Wood panels (not the actual Sir Henry Wood pieces that were baseball swing out) with just a standard wood seal. Blusher the pieces that were cut kayoed with a dark red acrylic. Position the convention over the wood and trace where the pieces will happen, this helps when you glue connected the pieces thus that you can put them in the right place. Glue the pieces onto the wood! You posterior use contact cement, wood mucilage, or even super glue if you are careful. I taped a piece of red see-through paper onto the back of the original piece that was contract out of to provide a background. This is a super simple project that can be modified in and so many shipway so I am not loss to elaborate any promote.

Step 7: Building the Frame

I am not going to speak for much about the frame construction due to that non being very explainable. This project does not even need a frame if you don't feel ahead to the task, but if you are I will provide pictures that will give ideas. If you are expiration to anatomy the frame and want directions, invite the comment bar, and I will send off elaborated directions.

Step 8: The Fattening Symbol

I hope you enjoyed this project and I hope to publish other Headliner Wars fan art including Darth Maul, and Vader. Make sure to ask questions if you have any and I will try out to resolve chop-chop.

Be the First to Share

Recommendations

  • Anything Goes Contest 2022

    Anything Goes Contest 2022